Position heater box assembly as shown onto the masked off portion of the firewall and mark the mounting holes. Methods of mounting the heater box unit is up to the installer’s discretion. For easy installation purposes, we have used self-tapping screws. The recommended method is to use nutsert. Predrill the marked holes for whichever method […]
*Beginning note, our bolt hole specifications are tight. Die grinding powder coated bolt holes in our components may be necessary to install the bolts. *Trimming on the bottom lip of the factory front bumper is required for the Shackle Reversal Crossmember. *On the Rox Front bumper with receiver hitch will not clear the Shackle Reversal […]
*READ INSTRUCTIONS THOROUGHLY BEFORE BEGINNING. OTR IS NOT RESPONSIBLE FOR INCORRECT INSTALLATION OR LOCAL LAWS REGARDING AFTERMARKET ACCESSORIES. THE USER IS RESPONSIBLE FOR ALL LIABILITIES ASSOCIATED WITH THE INSTALLATION AND USE OF THIS PRODUCT. ALWAYS UTILIZE PERSONAL SAFETY EQUIPMENT WHEN YOU ARE WORKING IN THE SHOP. DISCONNECT BATTERY BEFORE YOU BEGIN. *These instructions serve as […]
Contents: (6) 8mm x 20mm Stainless Steel Button Head Bolts (2) 8mm x 25mm Stainless Steel Button Head Bolts (2) M8 Flange Nuts (8) 8mm Stainless Steel Flat Washers (12) ⅜” x ¾” Stainless Steel Button Head Bolts (12) ⅜” Serrated Lock Nuts (4) ¼” Serrated Lock Nuts (4) Black Door Hinge Nuts – Installed […]
Hardware Contents: (8) 8mm Flange Head Bolt (4) 8mm Steel Lock Flange Head Bolt (2) 12mm Socket Cap Bolt (2) 12mm Flat Washer Not included only required for 2018-2019 Models You will need (1) 12mm-1.75 thread tap Begin by removing the factory rear end caps. Locate the 12mm-1.75 metric thread tap from the hardware. Use […]
Rox Slider Kit for the Mahindra Roxor Includes: (14) 5/16” SS BH Bolts (10) 5/16” Serrated Flange Head Bolts (24) 5/16” Serrated Flange Lock Nuts Begin by removing Rox Sliders and hardware from packaging. Verify all the components listed above are there. Rox Sliders come bolted together for packaging, unbolt them and set on padded […]
Rear full floater kit for the Mahindra Roxor Includes: Yukon 30 Spline Chromoly Axle Shafts Wheel Hubs Spindles Timken Bearing and Seal Kit Spindle Nut Kits Wheel Studs 27 Spline Drive Flanges Gaskets Caps Grade 8 Hardware Begin by safely lifting the Roxor up in the air with either a lift or safely set on […]
*READ INSTRUCTIONS THOROUGHLY BEFORE BEGINNING. OTR IS NOT RESPONSIBLE FOR INCORRECT INSTALLATION OR LOCAL LAWS REGARDING AFTERMARKET ACCESSORIES. THE USER IS RESPONSIBLE FOR ALL LIABILITIES ASSOCIATED WITH THE INSTALLATION AND USE OF THIS PRODUCT. ALWAYS UTILIZE PERSONAL SAFETY EQUIPMENT WHEN YOU ARE WORKING IN THE SHOP. Included but not shown in the picture above, is […]
Begin by preparing and cleaning both mating surfaces, the oil pan skid plate, and the bottom of the oil pan. Sand the bottom of the oil pan down to bare metal with 36-40 grit sandpaper, and make sure there is no residue or dust left by wiping both surfaces with a wax and grease remover. […]
If you have made modifications to your Mahinda ROXOR such as oversize wheels and tires, ECU flash / tune, and/or regearing, you are likely exerting more stress on the front frame rail than it was intended for out of the factory. All parts are subject to wear and tear over time, but if you’re playing […]
Monday – Thursday
6:00 A.M. to 5:00 P.M.
Lunch from 12 P.M. to 1 P.M.
Westfab Custom
Fabrication, LLC